Our service for you

TRAINING

KOMPPLAN COMPRESSOR TRAININGS

REASONABLE AND INDISPENSABLE

„Of course trainings cost money. You can invest your money in machinery, cars or real estate. And… you can also invest in something with lasting benefits and immediate profit: your own knowledge and skills!”

KOMPPLAN compressor workshops are necessary and useful, especially if you want to ensure the safe operation and proper handling of your compressor system. These workshops may even be compulsory for certain diver’s certificates or for fulfilling legal provisions.

At large filling stations and diving centers failure of a compressor or filling contaminated air due to inadequate or inexpert maintenance usually causes considerable losses in both image and finances. This can only be prevented by profound technical knowledge and proper handling of the compressor system.

Compressors are no overly complicated constructions – the basic knowledge taught at our workshops should be well sufficient to properly operate your compressor and carry out the most important maintenance work and minor repairs.

Contact person

Stephan Adam

stephan adam 1 - Training

Our Trainings:

  • Compressor technology, filling systems - Basic

    Target group:
    Participants from sectors like fire services, civil protection, scuba diving, industry, breathing-air in general. Participants of the operators’ training and persons with extended experience in operating high-pressure compressors, who want to extend their knowledge and skills with regard to troubleshooting and fault correction. Also who want to complete and update their knowledge and skills with regard to pure breathing-air in acc. with DIN EN 12021:2014 and/or ISO 8573-1.
    Apart from the controls, the seminar is independent of manufacturer.

    Content:
    Troubleshooting in prepared units Competent troubleshooting, fault localization and correction Specific instructions on electronics and controls of IDE-HMI Control, IDE-TCC Compressor-Control, IDE Fill-Control, IDE AIRSAVE ULTIMATE, AIRSCRUBBER C02 + AIRSCRUBBER C02/C0 Air processing systems, breathing-air analysis in acc. with DIN/EN 12021-2014 System set-up, appropriate compressor room, planning assistance Discussion of specific customer problems

    Benefit:
    In this training participants gain the additional competence to define and operate different compressor controls, to determine mechanical and electrical faults and to run a breathing-air analysis. Upon successful completion the participants receive a certificate (valid for 3 years)
    Please bring appropriate protective clothing with you

    Duration:
    1 day

    Number of participants:
    6 -12

    Location:
    IDE-Kompplan
    Compressed Air Solutions
    Geigelsteinstrasse 10
    83080 Oberaudorf/ Germany

    Times:
    Day 1: 8.30 am – 12.00 pm and 1.00 pm – ca. 5.30 pm

    Dates:
    12.May 2020, 20.October 2020

    Registration:
    Online registration

    Course fee:
    EUR 400,00, the seminar price includes participant certificate, seminar documents, seminar drinks, lunch, afternoon coffee with biscuits.

  • Compressor technology - professional

    Target group:
    Participants from sectors like fire services, civil protection, scuba diving, industry, breathing-air in general.
    Participants of the basic technical training and persons with extended experience in operating high-pressure compressors, who want to extend their knowledge and skills with regard to the technical structure and functions of the compressor.
    The seminar is independent of manufacturer

    Content:
    Troubleshooting and repairs in a prepared unit Internal parts of a compressor block from the T 120/121 3 – 11 kW series Competent troubleshooting, fault localization and repair, Adjusting and checking safety devices, Compliance with regulations, documentation, How to order the correct expendables Discussion of specific customer problems

    Benefit:
    In this training participants gain the additional competence to detect and repair faults, malfunctions and defects of a high-pressure piston compressor, and to adjust and check all safety devices in a high-pressure compressor filling system.
    Please bring appropriate protective clothing.
    Upon successful completion the participants receive a certificate

    Duration:
    1 day

    Number of participants:
    8 – 12

    Location:
    IDE-Kompplan
    Compressed Air Solutions
    Geigelsteinstrasse 10
    83080 Oberaudorf/ Germany

    Times:
    8.00 am – 12.00 pm and 1.00 pm – ca. 5.30 pm

    Dates:
    13.May 2020 21.October 2020

    Registration:
    Onlineregistration

    Course fee:
    EUR 420,00
    When booking with the technic basic seminar the day before: € 750.00 together for both seminars

  • IDE MG Membrane System with high-pressure compressor operators‘ training

    Target group:
    Participants from the scuba sector. Persons who use or are interested in a NITROX MEMBRANE high pressure filling system, and who want to operate it competently and safely, e.g. compressor managers, dive shop employees, persons to be entrusted with operating the system or users who want to be authorized to fill Nitrox cylinders.
    Prerequisites:
    successful completion of the compressor technology BASIC training.

    Content:
    Basic function, Operating the system, Safety regulations of the Technical Regulations for Compressed Gases, Ordinance on Industrial Safety and Health, breathing-air standard DIN/EN 12021:2014 Compressor controls IDE HMI-TC CONTROL with AIRSAVE ULTIMATE OG, Accident prevention rules, particularities for handling O2. Ordering spare parts and consumables Rules on maintenance and installation, How to handle and remedy malfunctions

    Benefit:
    Successful completion of this training enables you to competently operate and/or maintain a IDE- NITROX MEMBRANE filling system. Upon successful completion the participants receive a certificate (valid for 3 years).

    Duration:
    1 day

    Number of participants:
    6 -12

    Location:
    IDE-Kompplan
    Compressed Air Solutions
    Geigelsteinstrasse 10
    83080 Oberaudorf/ Germany

    Times:
    9.30 am – ca.4.30 pm

     

    Dates:
    by arrangement

    Registration:
    Mail/ Fax

    Course fee:
    EUR 450,00

WHY HIGH-PRESSURE COMPRESSOR WORKSHOPS?

Breathing-air, clean and pure in compliance with DIN EN 12021 (formerly DIN 3188) is a major prerequisite for safe diving. To ensure this, two essential requirements must be met: a filling station in compliance with strict technical regulations and proper operation. Above all, all relevant safety requirements must be observed strictly and thoroughly. Inexpert operation and subsequent failure of the compressor not only costs money, but also poses a risk of injury to personnel and divers.

The skills you will learn during the practical parts of the workshops and the technical knowledge from the theory parts will help you to operate and maintain a compressor system safely, competently, and in compliance with the relevant regulations.
As a commercial operator of a compressor and / or a filling plant, they require proof of competence for the operation of the plant, as required by the operational safety ordinance. As soon as a donation to others takes place, an approval by the responsible authority is necessary!
This seminar gives you legal certainty regarding liability risks in the operation of filling systems. The know-how conveyed in our seminars for the operation of a compressor system for breathing air is based on the requirements of the Industrial Safety Ordinance (BetrSichV 2015) and the corresponding Technical Rules (TR 401), as well as the PED 2014/68/EU.

The theory part explains facts and functions of the compressor, as well as the legal provisions pertaining to the operation of a filling station for breathing-air. Knowledge of these provisions is indispensable for all operators and will therefore be an important focus in our workshops. In the practical part we will teach you how to carry out maintenance work that the manufacturer scheduled to be done by the operator, and the necessary skills and knowledge to do minor repairs in consultation with the manufacturer.

REGISTRATION

Please register on our online registration page:
http://www.kompplan.de/en/trainings/online‐application/

or follow this path.
www.kompplan.de > English version > trainings > online registration

or
www.ide.de > Service > Seminare > then click the button “register now” next to the relevant training.

Please be aware that your registration is binding. You are only entitled to participate, however, after you received written confirmation from Kompplan and after receipt of the course fee in our account. We will send you an invoice and our bank details.

CANCELLATION

In the event of an insufficient number of participants we reserve the right to cancel the training up to 6 business days before the scheduled beginning. In this case we will refund your course fee advance payment.

You can also cancel the booked training until up to 8 business days before the scheduled beginning. You must do so in writing.

Afterwards we will invoice 70% of the course fee. We will not refund flight / train tickets and other travel expenses.

Please be aware that in case of unexcused absence from the training we will charge 100% of the course fees.

COURSE FEES

The course fee includes the current VAT rate, workshop documents and certificates, beverages, lunch and afternoon coffee with pastries.

For group bookings of three or more participants we grant a 10 % discount on all our trainings; for 6+ participants 15 % discount.

Special provisions for refresher and air-quality trainings: for 3+ participants 5%, for 6+ 10% discount.

HOTEL RECOMMENDATION

If you need hotel accommodation, we can recommend the following hotels. Contact for info and bookings:

close to IDE:

SPORTHOTEL WILDER KAISER
Astl-Reisen GmbH
Naunspitzstr. 1
D-83080 Oberaudorf
Phone: +49 (0)8033/925-0
Fax.: +49 (0)8033/3106
E-Mail: info@wilderkaiser.de

alternative:

Bernhards
Restaurant & Hotel
Marienplatz 2
83080 Oberaudorf
Phone: +49 (0)8033/ 30570
Fax: +49 (0)8033 / 305715
E-Mail: info@bernhards.biz

HOW TO FIND US

IDE-Kompplan
Compressed Air Solutions
Geigelsteinstrasse 10
83080 Oberaudorf/
Germany) 08033 97935-0

Seminare 2020 de - Training

THE CLASS ROOM

IDE-Kompplan

Phone: +49 (0) 1714205521

E-Mail: training@kompplan.de

Raum - Training

LOCAL TRAININGS

Upon request, and if the required devices and rooms are available, we can hold our trainings at your premises.
Please give us a call and we will gladly make you an offer.
We are looking forward to your participation!

IDE-Kompplan
Compressed Air Solutions